船用防避台风决策系统基本技术

运用相对运动原理求出船舶避离台风的基础可航扇区；根据预报的风浪场，计算出产生船舶“谐摇”的扇区；根据船舶性能和波浪预报，用等航时线法求出最少航时扇区；采用最优控制理论，在基础可航扇区内剔除“谐摇”扇区，并与最少航时扇区进行优化，最终得到既安全又省时的船舶避离台风的最佳可航扇区。把防避台风的整个决策过程开发成业务化的软件包，从技术上帮助船长加快避台决策速度，提高避台实施精度，达到安全经济的防避台风的目的。     

用动态规划方法优化设计船舶车辆甲板结构

基于规范的车辆甲板结构优化设计在数学上是一个较大的非线性规划问题，而且为了满足实际需要，其中一些变量只能离散变化。本文将该问题处理为三阶段决策问题，因而能运用动态规划方法有效地求解。通过一个实例详细说明求解过程，从中看出应用动态规划方法解决基于规范的船舶结构优化设计问题的特色。     

抛锚碰擦球鼻的预报和防止

本文介绍在总体设计时防止抛锚碰擦船首球鼻的计算方法，以预测和防止事故发生。     

船舶浮态计算方法及船舶浮态图谱

本文用化非线性问题为线性问题的线性化方法,对非线性隐式的船舶浮态方程组进行了数值解,并在深入研究的基础上提出了两种形式浮态图谱,以便能迅速而准确地确定船舶各种不同装载情况下的浮态。本文给出了五万吨油轮“西湖”号算例。     

The Reinforcement Analysis of Prestressed Anchor Frame Beam in the Deep Cutting Slope under Three Dimensional Strong EarthquakeEI北大核心

Research purposes: In order to further study the reinforcement of prestressed anchor frame beam in the deep cutting slope under three dimensional strong earthquake, a model of the deep cutting slope is built through FLAC 3D simulation software, the seismic wave to the model from three directions of x,y and z is input, and the dynamic response of the slope is analyzed. Then, the prestressed anchor frame beam reinforcement measures are applied to the model, and this paper analyzes the reinforcement effect of the prestressed anchor frame beam to the deep cutting slope under three dimensional strong earthquake. Research conclusions:(1) The prestressed anchor frame beam has a good effect on restraining the horizontal displacement of the deep cutting slope. (2) Under the three dimensional strong earthquake, the prestressed anchor frame beam has a good effect on the horizontal acceleration and horizontal velocity of the deep cutting slope, which reduces the peak of horizontal acceleration and horizontal velocity. (3) Through the comparison of the response before and after the reinforcement of the prestressed anchor frame beam is given under the 9 degrees three dimensional strong earthquake, it can be concluded that the prestressed anchor frame beam can provide good reinforcement effect to the deep cutting slope. (4) This research can be used for reference to the earthquake resistance of the slope engineering. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

三相交流电动转辙机5线制道岔电路模拟试验新方法

提出了三相交流电动转辙机道岔室内模拟试验新电路,它适用于客运专线及高速铁路正线S700K电动转辙机或ZYJ7电液转辙机5线制道岔电路的模拟试验,能够全面试验道岔室内动作和表示电路,克服了以往道岔电路试验不彻底的缺点。     

三轴汽车前后轮角输入时的响应特性

本文详细推导了三轴汽车线性二自由度模型的运动微分方程，分析了汽车对前后轮角输入时的移居记响应特性。从汽车动力学的角度讨论了前后轮转应具备的比例关系。该方法同样适用于其它多轴汽车的建模分析。     

Greenhouse gas emissions from ships in ports – Case studies in four continents

Emissions of GHG from the transport sector and how to reduce them are major challenges for policy makers. The purpose of this paper is to analyse the level of greenhouse gas (GHG) emissions from ships while in port based on annual data from Port of Gothenburg, Port of Long Beach, Port of Osaka and Sydney Ports. Port call statistics including IMO number, ship name, berth number and time spent at berth for each ship call, were provided by each participating port. The IMO numbers were used to match each port call to ship specifications from the IHS database Sea-web. All data were analysed with a model developed by the IVL Swedish Environmental Research Institute for the purpose of quantifying GHG emissions (as CO₂-equivalent) from ships in the port area. Emissions from five operational modes are summed in order to account for ship operations in the different traffic areas. The model estimates total GHG emissions of 150,000, 240,000, 97,000, and 95,000 tonnes CO₂ equivalents per year for Gothenburg, Long Beach, Osaka, and Sydney, respectively. Four important emission-reduction measures are discussed: reduced speed in fairway channels, on-shore power supply, reduced turnaround time at berth and alternative fuels. It is argued that the potential to reduce emissions in a port area depends on how often a ship revisits a port: there it in general is easier to implement measures for high-frequent liners. Ships that call 10 times or less contribute significantly to emissions in all ports.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

Tuning of transfer functions for analysis of wave–ship interactions

Transfer functions are often used together with a wave spectrum for analysis of wave–ship interactions, where one application addresses the prediction of wave-induced motions or other types of global responses. This paper presents a simple and practical method which can be used to tune the transfer function of such responses to facilitate improved prediction capability. The input to the method consists of a measured response, i.e. time series sequences from a given sensor, the 2D wave spectrum characterising the seaway in which the measurements are taken, and an initial estimate of the transfer function for the response in study. The paper presents results obtained using data from an in-service container ship. The 2D wave spectra are taken from the ERA5 database, while the transfer function is computed by a simple closed-form expression. The paper shows that the application of the tuned transfer function leads to predictions which are significantly improved compared to using the transfer function without tuning.